Milwaukee 9568 Uživatelský manuál stáhnout pdf (Strana 1)

The use of any hoist presents some risk of personal injury

or property damage. That risk is greatly increased if proper

instructions and warnings are not followed. Before using this

hoist, each operator should become thoroughly familiar with

all warnings, instructions, and recommendations in this

manual.

Retain this manual for future reference and use.

Forward this manual to the hoist operator.

Failure to operate the equipment as directed in the manual

may cause injury.

Before using the hoist, fill in the information below. Model and

serial numbers are stamped into the aluminum hoist housing.

Model Number

Serial Number

Purchase Date

ollow all instructions and warnings for

inspecting, maintaining and operating this hoist.

ELECTRIC CHAIN HOIST

The equipment described and illustrated in these

instructions is intended for industrial use only and

should not be used to lift, support or otherwise

transport people.

Catalog No. Rated Load

9560 1/2 Ton

9561

9562

9565 1 Ton

9566

9567

9568

9570 2 Ton

9571

9572

9573

OPERATOR’S

MANUAL

1 2 3 4 5 6 ... 31 32

Shrnutí obsahu

Strany 1 - OPERATOR’S

The use of any hoist presents some risk of personal injuryor property damage. That risk is greatly increased if properinstructions and warnings are no

Strany 2 - WARRANTY

93. Carefully raise load block to upper limit and observe if itstops automatically at desired level. Do not allow load blockto run into hoist housing

Strany 3 - SAFETY PRECAUTIONS

Limit Switch ShaftRemove any dirt accumulation and spray with a generalpurpose lubricant.Hook BearingApply a few drops of SAE 30 gear or motor oil aro

Strany 4 - HOIST SPECIFICATIONS

115. Remove four screws attaching gear box cover to gearhousing and remove gear box cover. Limit switch drive shaftwill come along with the cover.6. I

Strany 5 - INSTALLATION

12Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878Figure 9A — Wiring Diagram for 1-Speed, 1-Pha

Strany 6 - OPERATION

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878131. Limit switch not operating 1. Check adjust

Strany 7 - MAINTENANCE

INSPECTION AND MAINTENANCE CHECK LISTELECTRIC POWERED OVERHEAD CHAIN HOISTType of Hoist ______________________________________________________ Capacit

Strany 8

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-387815INSPECTOR’S REPORTITEM REMARKS (LIST DEFICIEN

Strany 9 - LIMIT SWITCH ADJUSTMENT

16316151472121468101351 Motor 1(See Figures 13 & 14)2 Sheave Housing Screw 43 Sheave Housing 1/2 Ton 11 & 2 Ton 14 Gear Housing1/2 Ton 11 &

Strany 10 - LUBRICATION

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-387817Figure 13 - Hoist Motor, 1-Phase1016132348751

Strany 11 - HOIST REPAIRS

18Figure 14 - Hoist Motor, 3-PhaseMilwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878265417983Part

Strany 12

Milwaukee Electric Tool Corporation A company within the Atlas Copco Group13135 West Lisbon Road • Brookfield, WI, U.S.A. 53005Alterations or modifica

Strany 13 - TEL: (800) 729-3878

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878191 Disc Brake Assembly1/2 hp, 115/230V 11 hp,

Strany 14 - TROUBLE SHOOTING

20Figure 16 - Electrical PartsMilwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-38781 Gear Box Cover

Strany 15 - TROUBLE SHOOTING (Continued)

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-387821Figure 17 - Limit Switch Parts715171661310912

Strany 16 - MILWAUKEE

22Figure 18 - Pushbutton StationMilwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878126710114513141

Strany 17 - Figure 12 - Basic Hoist

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878231 Pushbutton Station & Control Cable Asse

Strany 18

24Figure 19 - Transmission PartsMilwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878121421393118723

Strany 19

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878251 Sheave Housing 1/2 Ton 11 & 2 Ton 12 Ge

Strany 20

26Figure 20 - Chaining PartsMilwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-38782-Ton Models1-Ton M

Strany 21 - Figure 16 - Electrical Parts

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878271 Sheave Housing 1/2 Ton 11 & 2 Ton 12 G

Strany 22

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878AUTHORIZED WARRANTY REPAIR CENTERS AND PARTS DE

Strany 23

2Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878SAFETY PRECAUTIONSEach MILWAUKEEElectric Chain

Strany 24

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878UNITED STATES29NEW YORK**ABC ELECTRIC 24-25 46

Strany 25 - 1 & 2 ton models

30Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878NOTES

Strany 26 - * Not Shown

31Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-3878NOTES

Strany 27 - Figure 20 - Chaining Parts

3MILWAUKEEElectric Chain Hoists are rugged, portable hoiststhat provide quick, precise lifting.The hoists are constructed oftough, but lightweight, di

Strany 28

APPLICATION INFORMATION This hoist is intended for general industrial use for lifting andtransporting freely suspended material loads within its rated

Strany 29

Milwaukee Electric Tool Corporation13135 West Lisbon RoadBrookfield, Wisconsin 53005TEL: (800) 729-38782. Before operating the hoist, be sure to obser

Strany 30

11. Do not operate unless hook travel limit devices function.Test without load each shift.12. Do not operate when hoist is not centered over load.13.

Strany 31

7CHAINChain is to be kept clean and lubricated (See LUBRICATION,page 9). Visually check chain every time hoist is used. Hoistmust not be operated when

Strany 32

Chain Replacement with No Chain in HoistRefer to Figures 4 and 5.1. DISCONNECT HOIST FROM POWER SUPPLY and movehoist to a work table. Do not remove th